Details
A broad tangle of arching mangrove roots that spreads across the floor of a tank or terrarium, with open archways an animal can pass through and shaded hollows underneath. It reads as weathered wood that has been in the enclosure for years, and it gives plants, moss and substrate something natural to grow around.
π Full Product Description
The Wide Mangrove Root is modeled on the stilt roots of a mangrove tree: a low, wide crown of branching roots that arch down to the ground and leave large openings between them. The surface carries a fine bark and wood-grain texture, so the piece looks like aged root wood instead of a smooth plastic ornament.
It stands on its own on a broad, spreading root base. Place it on the substrate as a centerpiece, tuck it into a corner, or plant around it. The gaps between the roots work as several caves, tunnels and pass-throughs, and the upper roots give climbing species a route off the ground.
It is offered in two versions. The PETG Wet Model is the one for water and humidity, a fit for the look of betta, shrimp and pleco aquariums and for humid setups such as crested gecko and dart frog vivariums. The PLA Dry Model is for dry enclosures and display, such as jumping spider, tarantula and temperate isopod setups, dioramas and tabletop terrain.
You receive one unpainted Wide Mangrove Root in the version you choose. Openings vary in size across the piece, so please compare the listed dimensions and the openings shown in the photos against your own animals before ordering.
βοΈ Key Features
β Wide, branching mangrove root shape with a natural wood texture
β Several caves, tunnels and open archways between the roots
β Freestanding on a broad root base, no mounting needed
β PETG Wet Model for aquariums, paludariums and humid vivariums, printed denser for submerged use
β PLA Dry Model for dry terrariums, dioramas and display only
β One size, printed as a single piece
β Ships unpainted in a solid filament color
β Made to order, printed individually
π§± Material Options
PETG Wet Model
Choose this for aquariums, paludariums, misted or bioactive vivariums, partially submerged placement and enclosures with UV lighting. It ships unpainted. PETG handles prolonged moisture and UV better than standard PLA, but that is not a guarantee: continuous high-output UV can still make it brittle over time, and no printed plastic is permanently waterproof or indestructible. For submerged pieces I add holes for air to escape and increase the density of the infill.
We print the Wet Model with denser infill than the Dry Model so it is better suited to sitting underwater. Printed pieces can still hold trapped air at first, so it may need a little time, a gentle tilt to release bubbles, or some substrate around the base to settle in your tank.
PLA Dry Model
Choose this for arid or low-humidity terrariums, dioramas, tabletop terrain and shelf display. It is lighter and is not made for water, constant moisture or strong UV. PLA versions are not recommended for submerged aquarium use.
π§ Setup, Use & Care
Aquarium use (PETG Wet Model only)
π§ Rinse with clean water before first use. Do not use soaps, detergents or cleaners.
π Inspect the piece and check every opening against the animals in your tank.
πͺ¨ Position it so it cannot shift, tip, trap an animal or press against the glass.
π«§ Tilt it underwater to release trapped air, and bed the base into the substrate if needed.
π Watch your animals after adding it, and check it during normal maintenance.
π« Remove it if it becomes damaged or develops a sharp edge.
Terrarium, vivarium and paludarium use
π‘οΈ Confirm the material and design suit your habitatβs temperature, humidity, lighting and species. Use the PETG Wet Model anywhere humid or misted.
π₯ Keep it away from heat lamps and heating elements.
βοΈ Set it firmly on the substrate so it cannot tip.
π Check the openings against the adult size of your animals.
π§Ή Inspect regularly for wear and trapped waste.
π Species-specific husbandry guidance always comes first.
Cleaning
πΏ PETG: clean water and a soft brush. No soap, bleach, solvents, abrasives, boiling water or dishwasher. Dry fully before storage.
π§½ PLA: a soft brush or lightly damp cloth. Keep away from heat.
π Dimensions
Length Γ width Γ height:
S1 5.9 Γ 4.1 Γ 3.2 in (150 Γ 105 Γ 81 mm)
S2 6.7 Γ 4.7 Γ 3.6 in (170 Γ 119 Γ 92 mm)
XL 7.5 Γ 5.2 Γ 4.1 in (190 Γ 133 Γ 103 mm)
Because each item is individually 3D printed, minor dimensional variation may occur.
π¨ Color and Appearance
Each piece is printed in a solid filament color and is not painted. Any painted or weathered examples in the photos show what finishing can look like and are not what ships. Color varies with lighting, photography, monitors and filament batch, and it can look different underwater or under enclosure lighting, so an exact match to the photos is not promised.
π¨οΈ About 3D Printing
This piece is made by FDM 3D printing. Visible layer lines, small seams, slight texture changes and light support-contact marks in recessed areas are a normal part of the process and are not defects. Each root is produced individually, not injection molded.
π οΈ Made to Order
Your root is printed individually after you order, so minor differences from piece to piece are normal. It ships as a single piece. Production time is separate from shipping time.
β οΈ Safety and Compatibility
This is decorative habitat decor, not a toy. You know your animals and enclosure best, so it is your decision whether the size, material, openings, surfaces and placement suit them. Do not let animals chew or ingest the piece, and remove it if it becomes damaged, since broken pieces can be a hazard. CurioPrinta cannot account for every species, behavior, enclosure, water chemistry, temperature or routine.
Species names in this listing are for search and design context, not a compatibility claim.
π¦ What Is Not Included
You receive one Wide Mangrove Root in the version you select. Everything else shown in the photos is for illustration only:
πΏ Plants, moss and substrate
πͺ¨ Rocks, wood and other props
π Animals of any kind
π‘ Lighting and the enclosure itself
The piece ships unpainted and unfinished.
β FAQ
π§ Can this be placed underwater?
Yes, in the PETG Wet Model, which ships unpainted and is printed denser for submerged use. The PLA Dry Model is not for underwater use.
π«§ Will it sink?
The Wet Model is printed denser to help it sit underwater, but trapped air can make any printed piece lift at first. Tilt it to release bubbles and bed the base into your substrate if needed.
π¨ Is the aquarium version painted?
No. The PETG Wet Model is a solid filament color with no paint.
π§± Can I order this in PLA?
Yes. The PLA Dry Model is for dry terrariums, dioramas and display only.
ποΈ Can I paint it myself?
For dry display, yes. We do not recommend customer-applied paint on anything that will be submerged, and any paint or finish used in a habitat needs to be researched by you for your animals.
βοΈ Can it go under UV lighting?
Choose the PETG Wet Model. It handles UV better than PLA, though continuous high-output UV can still make it brittle over time.
πΏ How should I clean it?
PETG: clean water and a soft brush, no soap or chemicals. PLA: a soft brush or lightly damp cloth, away from heat.
π· Will it look exactly like the photographs?
Shape and texture will match, but color varies with filament batch, lighting and screens, and painted examples are not what ships.
π’ Is it suitable for my specific fish, reptile, amphibian, snail or shrimp?
We cannot say for any individual animal. Please compare the dimensions and openings with your animals and follow species-specific care guidance.
Designed by novYTerra