Details
A broad, weathered stone slab balanced on two gnarled rock legs, with a shaded cave tucked underneath. Platform Rock gives your animal two places in one: a flat lookout up top and a dark hideout below. Set it into sand or soil and it reads like a natural rock table worn down by wind and time.
π Full Product Description
Platform Rock is a 3D printed terrarium hide designed by novYTerra. The top is a wide, layered slab with a wind-carved surface texture, supported by two thick, knotted stone pillars. Between the pillars sits an open cave with a low entrance, so the piece works as a hide and a raised resting surface at the same time.
It is freestanding and sits on the substrate, so you can bed the legs into sand or soil for a grounded look, or set it on top for a taller profile. The slab gives climbing animals a raised spot to rest and look out, and the cave underneath gives shy animals a covered retreat. It also works well as a centerpiece for planting around, with moss or ground cover tucked against the legs.
For arid setups, the PLA Dry Model suits display and lower-UV builds for keepers of leopard geckos and tarantulas, and bearded dragon keepers often add a piece like this to a desert layout. Under strong basking UV, choose the PETG Wet Model instead. For humid, misted or bioactive builds, the PETG Wet Model fits crested geckos and dart frogs, plus tropical isopods. Always compare the cave opening, the height and the overall size against your own animals before use.
You receive one Platform Rock in the size and material you select, printed unpainted in a single solid color and shipped assembled in one piece. Plants, substrate, animals, lighting and the enclosure are not included.
βοΈ Key Features
β Original novYTerra design, printed and sold by CurioPrinta under commercial license
β Wide stone slab on two gnarled rock legs with a sheltered cave underneath
β Hide and raised resting surface in one piece
β Weathered, wind-carved rock texture for a naturalistic desert or forest look
β Freestanding: set it on the substrate or bed the legs in for a grounded look
β PETG Wet Model for humid, misted, bioactive and paludarium setups
β PLA Dry Model for arid terrariums, dioramas and display
β Three sizes, from about 5.6 to 9.3 inches long
β Ships assembled in one piece
β Made to order, printed individually for each order
π§± Material Options
PETG Wet Model
Choose PETG for misted, high-humidity, bioactive and paludarium setups, and for enclosures with strong UV lighting. PETG handles prolonged moisture and UV better than standard PLA, but it is not a guarantee: continuous high-output UV can still make it brittle over time, and it is not permanently waterproof, indestructible or chemically inert. PETG Wet Models ship unpainted.
PLA Dry Model
Choose PLA for arid terrariums, dioramas, tabletop terrain and display. PLA is for dry use only and should not sit in constantly wet enclosures or under strong UV. PLA versions are not recommended for submerged aquarium use.
π§ Setup, Use & Care
Terrarium, Vivarium & Paludarium Use
π¦ Confirm the material and design suit your habitatβs temperature, humidity, lighting and species.
π₯ Keep it away from heat lamps, heat mats and other heating elements.
βοΈ Set it on a firm, level base or bed the legs into substrate so it cannot tip.
π Check the cave opening and slab height against your animalβs adult size.
π§ For any part that will sit in water, use the PETG Wet Model only. The inside of the print is partly hollow and can trap air, so see the FAQ before placing it in water.
π Inspect it regularly for wear, sharp edges and trapped waste.
π Species-specific husbandry guidance always comes first.
Cleaning
πͺ₯ PETG: rinse with clean water and a soft brush. No soap, bleach, solvents, abrasives, boiling water or dishwasher. Dry fully before storage.
π§½ PLA: wipe with a soft brush or a lightly damp cloth, and keep it away from heat.
π Dimensions
Length Γ Width Γ Height
S1 5.6 Γ 3.5 Γ 2.0 in (142 Γ 90 Γ 52 mm)
S2 7.4 Γ 4.7 Γ 2.7 in (189 Γ 120 Γ 69 mm)
XL 9.3 Γ 5.9 Γ 3.4 in (236 Γ 150 Γ 86 mm)
Because each item is individually 3D printed, minor dimensional variation may occur.
π¨ Color and Appearance
Platform Rock is printed in a solid filament color and is not painted. Painted photos show finishing examples only. Color can look different depending on lighting, photography, your screen and the filament batch, and it can shift under enclosure lighting, so an exact match to the photos is not promised.
π¨οΈ About 3D Printing
This piece is made on an FDM 3D printer, layer by layer. Fine layer lines, small seams, slight texture changes and support-contact marks inside the cave are a normal part of the process and are not defects. Each piece is produced individually, not injection molded.
π οΈ Made to Order
Every Platform Rock is printed individually after you order, so minor differences between pieces are normal. Production time is separate from shipping time. All sizes ship assembled in one piece.
β οΈ Safety and Compatibility
Platform Rock is decorative habitat decor, not a toy. You know your animals best, so you decide whether the size, material, openings, surfaces and placement suit them. Do not let animals chew or eat it, and remove it if it becomes damaged, since broken pieces can be a hazard. CurioPrinta cannot account for every species, behavior, enclosure, temperature or care routine.
Species names in this listing are for search and design context only and are not a compatibility claim.
π¦ What Is Not Included
You receive one Platform Rock in your chosen size and material.
π± Plants, moss and substrate
πͺ¨ Rocks and other props shown in photos
π¦ Animals
π‘ Lighting and the enclosure
π¨ It ships unpainted, in a single solid filament color
β FAQ
π§ Can this be placed underwater?
Platform Rock is listed for terrariums, vivariums and paludariums, not aquariums. If you place the PETG Wet Model in water, such as the water area of a paludarium, know that the inside of the print is partly hollow and can trap air, which may make it float. Making small vent holes lets the air escape. CurioPrinta does not add these holes, so that step is up to you. Never use the PLA Dry Model in water.
π¨ Is the wet version painted?
No. The PETG Wet Model ships unpainted, in a single solid filament color.
π§΅ Can I order this in PLA?
Yes. The PLA Dry Model is available in every size, for dry setups and display only.
ποΈ Can I paint it myself?
You can paint a PLA Dry Model for display. For any piece going into a habitat, especially a wet one, research any paint or coating carefully yourself before using it with animals.
π§½ How should I clean it?
PETG: clean water and a soft brush, no soap or chemicals. PLA: a soft brush or lightly damp cloth, kept away from heat.
βοΈ Can it go under UV lighting?
Choose the PETG Wet Model for enclosures with strong UV, such as desert basking setups. PETG holds up better than PLA under UV, though long exposure to high-output UV can still make it brittle over time. Keep either version away from heat lamps.
π· Will it look exactly like the photographs?
Close, but not exactly. Painted photos show finishing examples, and every print has its own small layer and texture differences.
π¦ Is it suitable for my specific reptile, amphibian or invertebrate?
That depends on your animal and setup. Check the cave opening, height and dimensions against your animalβs adult size and needs. CurioPrinta cannot guarantee it suits a specific animal.
Designed by novYTerra